1) Installing conditions
    A) Copier installation - Do not install your copier in areas that are:

• damp, humid, or very dusty
• exposed to direct sunlight
• poorly ventilated
• subject to extreme temperature or humidity changes, e.g., near an are conditioner or heater
• Be sure to allow the required space around the machine for servicing and proper ventilation.

    B) Power Source

• Use an exclusive-use power outlet. If the power plug of this machine is inserted into a power outlet commonly used with other illumination units, flickers of the lamp will result. Use a power outlet which is not commonly with any illumination units.
• Avoid complex wiring.

    C) Grounding the wire connection.

• To avoid danger, be sure to connect a grounding wire. If no grounding wire is connected and leakage occurs, a fire or an electrical shock may occur.

2) Removal of protective material and fixing screw.
    A) Remove all tape and protective material.

• Remove all tapes, then open the document cover and remove the protective materials of sheet shape.

    B) Remove the fixing screw.

• Use a coin to remove the optic fixing screw located on the upper-left-side exterior panel.
• The fixing screw is required when transporting the machine. There is a slot to store it in the paper tray.

1) Open the manual tray, and open the side cover.


2) Open the front cover (Hold both sides and pull down to open).


3) Loosen the screw and remove the developer cartridge.
Note: When handling the developer unit be careful not to bend or distort the plastic shield just above the magnetic roller.



4) Remove the brass colored screws which fix the toner hopper and developer unit then separate the two halves for your copier model.


Note: If preforming developer replacement procedure it is necessary to remove all of the old developer from the unit first including that which is magnetically adhered to the magnetic roller. Turning the screw & gear on the end of the magnetic roller CLOCKWISE to rotate the magnetic roller will aid in the removal. Use of a vacuum cleaner is necessary being careful not to scrape the roller. Simulation 20 sub-code 1 resets the maintenance required warning light and simulation 42 sub-code 1 resets the developer replacement required warning light.

5) Supply developer along the developer tank and over the stirring auger.
Note: Shake the developer bag enough before opening it. Be careful not to splash developer outside Developer unit. THE ENTIRE CONTENTS OF THE DEVELOPER BAG RE REQUIRED. If necessary turn the screw & gear on the end of the magnetic roller CLOCKWISE to allow more room.



6) Attach the developer tank to the developer cartridge.
Note: After supplying the developer into the developer cartridge, do not tilt or shake the developer cartridge.

7) Attach the developer cartridge to the copier, and fix it with the screw.

8) Insert the toner cartridge into the machine insuring that the cartridge in seated FIRMLY and COMPLETELY to the back of the machine. Failure to insert the toner cartridge completely may result in a clicking sound and possible failure of the toner cartridge.

9) Assure that all setup procedures are correctly completed and apply power to the copier for the first time.
Note: The copier will now self-calibrate. THIS PROCESS MAY TAKE UP TO 5 MINUTES AND MUST NOT BE INTERUPTED.

10) When the green Stat Key indicater comes on steadily the copier is ready to make copies.

A) Developer counter re-setting.
   •Follow these instructions EXACTLY.
   •Press "Clear" - "Interrupt" - "Zero" - "Interrupt". Machine will blank off.
   •Use the number buttons to make display read "42". Press "Print" button. Machine will flash 00.
   •Use quantity buttons to make display read "01". Press "Print" button. Machine will flash 000
   •Press "Clear" - "Clear" - "Clear" - "Clear" and power machine off and back on.
   •Preform this procedure at you own risk. Incorrect entry of codes can disable machine requiring service call.

A) Maintenance counter re-setting.
   •Follow these instructions EXACTLY.
   •Press "Clear" - "Interrupt" - "Zero" - "Interrupt". Machine will blank off.
   •Use quantity buttons to make display read "20". Press "Print" button. Machine will flash 00.
   •Use quantity buttons to make display read "01". Press "Print" button. Machine will flash 000
   •Press "Clear" - "Clear" - "Clear" - "Clear" and power machine off and back on.
   •Preform this procedure at you own risk. Incorrect entry of codes can disable machine requiring service call.